坚朗300瓷砖胶

坚朗超强力瓷☆砖胶中含有多种添加剂具有高粘』结力、施工中不用浸砖湿墙、良好的柔韧性、抗渗、抗裂、抗老化性佳、环保施工简便。

适用范围
适用于内外水泥砂浆基面粘贴瓷片⌒，纸面砖，条形砖等其他中型规格瓷砖。

产品特点
1、绿色环保、无毒、无异味;             2、粘结能力强、防止产生空鼓;

3、具有良好的耐水与抗老化性能;             4、薄层施工， 减少用量，快捷方便;             

5、具有一定的抗渗功能，避免粘贴砖材的缝隙吐白。

表面处理：
1、所有表面应结实、干燥、清洁、不晃动、无油污、蜡渍和其他松散物;
2、油漆过的表面应作粗化处理至少暴露75%的原表面;新混凝土面完成后,需养护六周方可铺砖新抹灰的表面应至少ζ　养护七天方可铺砖;
3、旧混凝土和抹灰表面可使用洗涤剂清洁,然后用水冲洗干净。其表面经晾干后方可铺砖;
4、底材疏松、吸水性∴强或表面浮尘脏物难清理,可先涂上底油以有助于瓷砖的粘结;
5、在吸水率高大的底材或高温、干燥的环境卐下，施工前最好先润温基面至外干内湿状态。

施工方法
将粉料倒入水中搅拌成膏状应该照先加水后加粉剂方法使用。
按粉料:水=20公斤: 4.5升-4.8升配比。搅拌均匀即可施工; (搅拌时建议配合电动搅拌机)
在操作允许时间内，可对瓷砖位置进行调整，粘结剂完全干固后(大约24小时后可进行填缝工作施工24小时内,应避免重负荷压于瓷砖表面)
推荐 用齿型刮板将胶浆涂抹于工作面之上,使之均匀分布，并成一条条齿状(调整刮板与工作面夹角来控制胶浆厚度)。
选择齿型刮板大小应考虑工作面的平整度和瓷砖背面的凹凸程度。如瓷砖背面的︾沟隙较深或石材、瓷砖大于300*300mm ,则应该进行双面〗涂胶,即在工作面I和瓷砖背面同时涂上胶浆。

注意事项：
1、本产品¤适宜在5°C~35°C的环境下使用，胶浆应该根据天气条件控制在2 ~3小时内■使用完毕。
2、施用前必须先确认底材的垂直度及平整度。
3、切忌把已干结的胶浆加水混合再用。
4、雨天施工一定要做好庇护措施且保证贴砖后24小时内施工区域干燥性。
5、注意保留伸缩缝。铺贴完成24小时后,方可踏入或♂填缝。
6、对眼睛皮肤具有刺激性，与皮肤接触可能引起过敏远离孩童，避免接触皮肤。一旦触及眼睛，请立刻以清水冲洗或寻求医治，如不】慎吞服，请立刻寻求医治井出示该包装及标签仅在通风处处理。

产品储存：存阴々凉干燥处。保质期:未开启产品在干燥阴凉通风处可保存一年。

执行标准：JC/T547-2005《陶瓷墙地砖胶粘◥剂》。C1级


Jianlang 300 porcelain brick adhesive

Jianlang super strength ceramic brick adhesive contains a variety of additives with high adhesion, no need to soak brick wet wall in construction, good flexibility, impermeability, crack resistance, good aging resistance and simple environmental protection construction.

Scope of application
It is suitable for bonding porcelain slices, paper tiles, strip tiles and other medium-sized tiles on the base of internal and external cement mortar.

Product characteristics
Green environmental protection, non-toxic, no odour;
Strong bonding ability to prevent the production of empty drums;
It has good water resistance and aging resistance.
Thin layer construction, reduce the amount of consumption, fast and convenient;
It has certain impermeability function to avoid whitening the gap of bonded brick.

Surface treatment

. All surfaces should be strong, dy, clean, non-sloshing, oil-free, wax stains and other loose matter;
. The painted surface should be coarsened to expose at least 75% of the original surface, and the new concrete surface should be cured for six weeks before laying the brick for at least seven days.
Old concrete and plastering surfaces can be cleaned with detergent and then washed with water. The surface of the brick can only be laid after drying;

. The bottom material is loose, the water absorption is strong or the surface floating dust dirty matter is difficult to clean, can first apply the bottom oil to help the ceramic tile bond;

In the high water absorption of the substrate or high temperature, dry environment, it is best to moisturize the base surface to the outside dry and internal wet state before construction.

Construction method
. The powder should be poured into the water to form a paste, which should be used according to the method of adding water and then adding powder.
. According to powder: water 20 kg: 4.5 liters 48 liters. The construction can be carried out by mixing evenly. (it is suggested to cooperate with the electric mixer when mixing.)
. Within the allowable time of operation, the position of the tile can be adjusted and the binder can be completely dry and solidified (within 24 hours of filling work, the burden on the surface of the tile should be avoided).
It is recommended that the mortar be smeared on the working face with a tooth scraper so that it can be evenly distributed and in a toothed shape (adjust the angle between the scraper and the working face to control the thickness of the mortar).
( the flatness of the working face and the concavity and convexity of the back of the tile should be taken into account in the selection of the size of the tooth scraper. If the gap on the back of the tile is deeper or the stone and tile are larger than 300300mm, the double-sided coating should be carried out, that is, the working face I and the back of the tile should be coated with glue at the same time.

Matters needing attention
This product is suitable for use in the environment of 5 "C ~ 35" C. the mortar should be controlled within 2 ~ 3 hours according to the weather conditions.
The verticality and smoothness of the substrate must be confirmed before application.
Do not mix the dried mortar with water for reuse.
The construction on rainy days must do a good job of sheltering measures and ensure the dryness of the construction area within 24 hours after the brick is affixed.
Pay attention to retaining the expansion joint. Only after 24 hours of paving can you step in or fill the seam.
Irritating to the skin of the eye, contact with the skin may cause allergies to stay away from children and avoid contact with the skin. -if you touch your eyes, please rinse with clean water or seek medical treatment immediately. If you accidentally swallow it, please immediately seek treatment well and show the package and label for handling only in the ventilation area.

Product storage
Keep it in a cool, dry place. Shelf life: the unopened product can be preserved in a dry, cool and ventilated place for one year.

Implementation standards：JC/T547-2005 "Ceramic Wall and floor Brick adhesive". C1 level